krock83 Member 2013-Apr-10 4:55 pm Actually Error Loading Flash Boot Process Failed Last edited by nopixel; 09-02-2013 at 12:13 AM. Copy Xmodem Flash Note:The LED position can vary slightly, which depends on the model.

Not a Switch> prompt... Check This Out Choose the Xmodem protocol in the Send File dialog box and click Browse in order to select the IOS image (.bin file) that you downloaded from Cisco. The IOS image is a bin file, not a directory.Do this first:dir flash: Make note of the contents in flash, namely the file that ends with .BIN. If the switch is in a continuous reboot, complete one of the procedures in this step, which depends on your switch model. Unable To Stat Flash/: No Such Device

If your Flash directory looks like this, proceed directly to Step 4. To speed the xmodem transfer up, change the Baud rate of the switch switch: set BAUD 115200 You will lose access to the console, but a restart of the HyperTerminal session Mounting Pictures on Wall - Child Safe [HomeImprovement] by nightdesigns354. Source If the boot command has failed or there is no valid image from which to boot in Flash, perform an Xmodem file transfer.

Be sure to verify that you have configured the correct boot statement on the switch. How To Boot Switch In Rommon Mode Quote + Reply to Thread « Previous Thread | Next Thread » Social Networking & Bookmarks Bookmarks Digg del.icio.us StumbleUpon Google Tweet CompTIA Cisco Microsoft CWNP InfoSec Practice Exams Forums See the Verify section of this document.

Not a Switch> prompt...

Verify Complete these steps: Issue the show version command in order to verify the current version of software that you run. Manufacturers work on hybrid memory and storage, Odinaff trojan hits banks Spiceworks Originals A daily dose of today's top tech news, in brief. You can do the same on your windows or mac laptop if you don’t have a separate TFTP Server.Step 3: Initialize flash:switch: flash_initStep4: Initialize Management Interfaceswitch: mgmt_initStep5: Assign IP address/Subnet Mask Cisco 3560 Rommon Tftp Loading "flash:c2960-lanbasek9-mz.122-37.SE1/c2960-lanbasek9-mz.122-37.SE1.bin"...flash:c2960-lanbasek9-mz.122-37.SE1/c2960-lanbasek9-mz.122-37.SE1.bin: no such file or directory Error loading "flash:c2960-lanbasek9-mz.122-37.SE1/c2960-lanbasek9-mz.122-37.SE1.bin" Interrupt within 5 seconds to abort boot process.

by Vapour1ze on Jul 9, 2013 at 2:13 UTC | Cisco 0Spice Down Next: Cisco asa 5510 TECHNOLOGY IN THIS DISCUSSION Cisco 344111 Followers Follow Join the Community! Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 *** The system will autoboot in 15 seconds *** Send break character to prevent autobooting. !--- Wait Last edited by nopixel; 09-01-2013 at 03:24 AM. have a peek here nhprice.com is neither a partner of nor an affiliate of Cisco Systems.

Use a terminal emulation program such as Microsoft Windows HyperTerminal in order to establish the console session. switch: dir flash: Directory of flash:/ 2    -rwx  976                      vlan.dat 3    -rwx  386                      system_env_vars 4    -rwx  5                        private-config.text 6    -rwx  1554                     config.text 24   drwx  192                      c3550-i5q3l2-mz.121-13.EA1 If you run a CMS image on a Catalyst 2970, 3550, 3560, or 3750, you can store the Cisco IOS image in an image directory. Output from a !--- Catalyst 2970, 3560, or 3750 varies slightly. 3550# Issue the show boot command in order to verify that the boot statement is set correctly.

However, if you use the Cluster Management Suite (CMS) image in order to manage switches with a web interface, you can store the Cisco IOS image file in its own directory. You probably will want to set the BAUD up to 115200 to speed up the transfer. Note: Do not use a CMS image (.tar file). Issue the boot system flash: directory/filename command.